Skip to main content
Version: 5.0 (Stable) ✅

SRS Linux Service

There are many ways to startup SRS:

  • Directly run srs at the trunk/objs, and need start again when system restart.
  • Linux service, the init.d scirpt at srs/trunk/etc/init.d/srs, and user can add to linux service when linked to the /etc/init.d/srs then add as service /sbin/chkconfig --add srs.

The SRS release binary can be downloaded from release site, we can install as system service.

Manual

We donot need to add to linux service to directly start SRS:

cd srs/trunk &&
./etc/init.d/srs start

or

cd srs/trunk &&
./objs/srs -c conf/srs.conf

init.d

Install and startup SRS as linux system service:

  • Build SRS: the install script will modify the INSTALL ROOT of init.d script.
  • Link to init.d: link the trunk/etc/init.d/srs to /etc/init.d/srs
  • Add to linux service: use /sbin/chkconfig for Centos.

Step1: Build and Install SRS

Intall SRS when build ok:

make && sudo make install

the install of make will install srs to the prefix dir, default to /usr/local/srs, which is specified by configure, for instance, ./configure --prefix=`pwd`/_release set the install dir to _release of current dir to use make install without sudo.

Step2: Link script to init.d:

sudo ln -sf \
    /usr/local/srs/etc/init.d/srs \
    /etc/init.d/srs

Step3:Add as linux service:

#centos 6
sudo /sbin/chkconfig --add srs

or

#ubuntu12
sudo update-rc.d srs defaults

Use init.d script

Get the status of SRS:

/etc/init.d/srs status

Start SRS：

/etc/init.d/srs start

Stop SRS：

/etc/init.d/srs stop

Restart SRS：

/etc/init.d/srs restart

Reload SRS：

/etc/init.d/srs reload

For logrotate(SIGUSR1):

/etc/init.d/srs rotate

For Gracefully Quit(SIGQUIT):

/etc/init.d/srs grace

systemctl

Ubuntu20 use systemctl to manage services, we also need to install init.d service, then add to systemctl:

./configure && make && sudo make install &&
sudo ln -sf /usr/local/srs/etc/init.d/srs /etc/init.d/srs &&
sudo cp -f /usr/local/srs/usr/lib/systemd/system/srs.service /usr/lib/systemd/system/srs.service &&
sudo systemctl daemon-reload && sudo systemctl enable srs

Remark: We MUST copy the srs.service, or we couldn't enable the service by systemctl.

Use systemctl to start SRS:

sudo systemctl start srs

Gracefully Upgrade

Gracefully Upgrade allows upgrade with zero downtime, it can be done by:

  • New SRS and old SRS should be able to listen at the same ports. They provide services in the same ports simultaneously.
  • The old SRS then closes listeners, and quit util all connections closed, this is Gracefully Quit.

Note: About more informations, please see #1579.

SRS3 supports Gracefully Quit:

  • Use signal SIGQUIT, or command /etc/init.d/srs grace
  • A new config grace_start_wait to wait for a while then start gracefully quit, default 2.3s
  • A new config grace_final_wait allows wait for a few minutes finally, default 3.2s
  • A new config force_grace_quit to force gracefully quit, see #1579.
# For gracefully quit, wait for a while then close listeners,
# because K8S notify SRS with SIGQUIT and update Service simultaneously,
# maybe there is some new connections incoming before Service updated.
# @see https://github.com/ossrs/srs/issues/1595#issuecomment-587516567
# default: 2300
grace_start_wait 2300;
# For gracefully quit, final wait for cleanup in milliseconds.
# @see https://github.com/ossrs/srs/issues/1579#issuecomment-587414898
# default: 3200
grace_final_wait 3200;
# Whether force gracefully quit, never fast quit.
# By default, SIGTERM which means fast quit, is sent by K8S, so we need to
# force SRS to treat SIGTERM as gracefully quit for gray release or canary.
# @see https://github.com/ossrs/srs/issues/1579#issuecomment-587475077
# default: off
force_grace_quit off;

Note: There is a example for Gracefully Quit, see #1579

Winlin 2019.10

©2013~2024 OSSRS Community